WFM kitchen set assembly instructions
Door disasembly
|
|
Press the fixation at the end of the hinge and move the hinge from the guide, holding down the front, securing it against damage |
 |
Drawer disasembly
 |
Shift the locking component to the outside of the drawer and pull out the drawer |
 |
Securing shelves
Safeguard used for shelf transportation may be used for securing shelves against accidental pulling out. Safeguards must be installed over the rear supports or left as installed for transport, preventing accidental pulling out and giving a safe shelf.
securing shelves
Securing the rear wall
Safeguards used for the rear wall are intended for improving cabinet stability for transport and storage, and influence durability of high and lower cabinets, transferring high loads during use. Installed rear wall safeguards may cause insignificant increase of cabinet dimensions. In case it makes it difficult to assembly the furniture set, safeguards may be removed before assembly using the screwdriver. Removing rear wall safeguards does not influence the furniture durability.
securing the rear wall
|
If the kitchen is L or U shaped, assembly must be started with the corner cabinet. Cabinet must be levelled using level and a spanner for foot adjustment |
 |
|
Foot must be mounted on the seat and adjusted to proper height. Foot adjustment spanner is available in the WFM offer |
 |
|
Each cabinet may be levelled by pressing on to the adjacent cabinet with a hand screw and combined using included screw joint.
|
 |
 |
Corner blind frame
|
|
Corner blind frame is fixed to the adjacent cabinet with screws
|
|
Screw is used to fasten the corner blind frame with front
|
 |
 |
Front end blind must be trimmed and fastened to the cabinet with the included angle plates (4 pcs.)
Blind base component
Blind front component |
 |
| Visible panel side | Panel components are fixed with included screws. | ||||
 |
|
 |
|
Visible upper component |
||||||||
|
 |
|
 |
|||||
End decorative panel assembly
| Spacing component | ||
 |
Complete panel with spacing components is fixed to the cabinet frame using included screws
Screw
|
 |
Internal decorative panel assembly
|
Spacing component |
 |
Angle plate |
Panel is fixed to one cabinet frame using screws and angle plates and to the other cabinet using screw with panel as in case of the end panel |
Screws |
Hanging bordering panel assembly
 |
Vertical and horizontal panel must be fixed to the cabinet using included screws. It is possible to fix panels to the wall using rawlplugs for assembly of wall shelves, available in the WFM offer. |  |
Lower bordering panel assembly
 |
Vertical and horizontal panel must be fixed to the cabinets using included screws |  |
Countertop assembly
| Bottom view of the combined boards |
 |
| Countertops are combined using screw joint and 10 mm spanner |  |
Before fixing, edges must be secured with wood adhesive, available in the WFM offer |
Cutting out holes
| Board edges must be secured with silicon or gap filling adhesive |
 |
| Holes for heating panel or the drainboard sink must be made with fret saw using the included template |
Covering boards, if required, may be combined using three board fasteners. Board joints and holes for assembly of e.g. drainboard sink or heating panel must be secured against water using silicone or gap filling adhesive.
Fixing lower profile to the countertop
Trim, make preliminary holes for screws, fix lower profile using screws.
Fixing upper profile and corners
Press the upper profile and corners.
Finishing skirting
Fix internal and external corners to the countertop with screws. Fix lower profile with screws and press the upper profile. Secure corners against water with silicone. Remove protective film. Press corners and finishing components.
 |
||
 |
 |
Securing against falling – upper
Fixing to the wall using screw with rawlplug
 Fixing component using screw to the cabinet frame
|
 |
| Screws included | |
Securing against falling – side
|
Fixing to the wall using screw with rawlplug
Fixing component using screw to the cabinet frame |
 |
| Screws included |
Preliminary skirting assembly
 |
 |
Slide the skirting fixing component into the guide in the foot and press.Move the skirting away from the foot with fixing component taped using two-sided adhesive tape. |
 |
Adhesive tape |
Combining skirting with fixing component, fixing skirting to the cabinet
 |
 |
Fasten the fixing component glued with skirting using screws |
|
Press the fixing component with skirting to the feet (clicking sound) |
 |
Installation of an air grate in the skirting
 |
 |
| Copy the air grate contour on the skirting | Put the air grate into the hole |
Combining skirting at an angle
|
Skirting fastener (90 deg.) external |
Skirting fastener (135 deg.) internal |
Skirting fastener (135 deg.) external |
 |
 |
 |
Assembly of the assembly slat for mounting hanging cabinets
 |
|
Slat must be levelled and fixed to the wall using rawlplugs. Drilling in the wall. Prepare holes for the slat, approx. 60mm below the upper edge of the high cabinet. Rawlplugs are included in the set (8 pcs. for a 2m slat). If there are high cabinets in the set for household devices, slat must be fastened in a way to provide the upper part of the hanging cabinet frames is at the same height as high cabinet. |
Levelling hanging cabinet
 |
Cabinet must be hanged on the slat and levelled |
|
|
Adjustment screw for cabinet inclination in relation to the wall |
 |
Adjustment screw for cabinet inclination in relation to the adjoining cabinet |
|
Mounting adjustment |
Combining hanging cabinets
 |
|
Hanging the end cabinet
 |
If there is an end cabinet in the set, it is hanged on the separate mountings and hooks
|
|
 |
End cabinet is fastened to the adjacent cabinet with screws in the places that are not visible from the outside (e.g. under the shelf).Screws included. |
Assembly of fronts
 |
 |
Depth adjustment
 |
|
|
Depth adjustment screw
|
Height adjustment
|
Height adjustment screw |
 |
Level adjustment
|
Level adjustment screw |
 |
Assembly of the drawer on the guides
 |
Drawer guides must be slid into the front. Put the drawer on the guides and slide the drawer. Catch will be automatically snapped. |
Assembly and adjustment of the drawer front
 |
 |
Side adjustment on the right side of the drawer |
|
|
2mm |
height adjustmen | ||
 |
Height adjustment |
||
|
Front assembly without tools |
|||
High drawer with skirting drawer
 |
 |
Skirting drawer adjustment
Inclination angle adjustment
Adjustment of the spring for the lifted front
Spring for the folding front
Adjustment of the spring for the folded front
ADESSO front handle assembly
| Tighten the screw with a screwdriver to clench the washer a little. Do not use electric driver.Screw and the washer are included in the set. |
Washer |
Screw
|
|
Handle |
 |
Do not use handles with narrow base or uneven base. It can cause the glass to crack |
|
ADESSO front (glass) |
Lighting installation
Removing the film from the full gloss PVC coated fronts
| Protective film must be removed carefully without any sharp tools from the full gloss fronts after the assembly. Wait 24 hours for the first cleaning of full gloss external surfaces. |
Trimming capping boards
Trim the capping boards at proper angle (board must be trimmed at the right angle to the surface of the board adjoining to the cabinet frame).
| Trimming board for ZWR-3 cabinet | Trimming board for the WR-3 cabinet |
 |
 |
Assembly of the capping board
|
Trimmed capping boards are fastened to the cabinet using included screws |
 |
|
Before tightening screws, trimmed edges must be coated with hot-melt adhesive in order to glue the boards |
